This updates the NAND stuff to Linux-3.11-rc1. It is synchronized
as best as we can get:
- locks removed
- The splitting in different files we had to better support different
features has been dropped. Instead this is now done mostly with the
use of __maybe_unused
Some barebox adjustments are forward ported, like:
- Allow partial page writes
- Optionally allow to erase bad blocks
- check for all_ff before writing a page
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This introduces the ecc stength fields in the structures and fills
them in, but leaves them unused right now.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This file is present in current kernels. In order to get closer
to current mtd support introduce it for barebox aswell.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This allows us to have some NAND specific stuff during registration,
like for example adding NAND specific device parameters.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This introduces a new NAND_BUSWIDTH_AUTO flag which can be used
to automatically detect the nand buswidth. The id is always read
in 8bit mode. An additional callback is needed to switch the nand
controller into 16bit mode.
This currently depends on a safe read_byte (always) and read_buf
(for onfi-only flashes) callback. It has been tested on OMAP, but
is not something that generally works. For this reason the existence
of the set_buswidth callback is used to determine whether we are
able to do autodetection or not.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
the code is taken from linux & u-boot implementations
Validated on an i.MX53 which gives the following log :
ONFI flash detected ... ONFI param page 0 valid
NAND device: Manufacturer ID: 0x2c, Chip ID: 0x38 (Micron MT29F8G08ABABAWP), page size: 4096, OOB size: 224
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Sync these limits with the Linux kernel. This allows support for NAND devices
with page size of 4k.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
code and in SoC code). Boards using the old way have CFG_NAND_LEGACY and
BOARDLIBS = drivers/nand_legacy/libnand_legacy.a added. Build breakage for
NETTA.ERR and NETTA_ISDN - will go away when the new NAND support is
implemented for these boards.
- allow for longer timeouts for USB mass storage devices
* Patch by Denis Peter, 11 Sep 2003:
- fix USB data pointer assignment for bulk only transfer.
- prevent to display erased directories in FAT filesystem.
* Change output format for NAND flash - make it look like for other
memory, too
Add support for LynuxWorks Kernel Downloadable Images (KDIs).
Both LynxOS and BlueCat linux KDIs are supported.
* Patch by Richard Woodruff, 25 Jul 2003:
use more reliable reset for OMAP/925T
* Patch by Nye Liu, 25 Jul 2003:
fix typo in mpc8xx.h
* Patch by Richard Woodruff, 24 Jul 2003:
Fixes for cmd_nand.c:
- Fixed null dereferece which could result in incorrect ECC values.
- Added support for devices with no Ready/Busy signal hooked up.
- Added OMAP1510 read/write protect handling.
- Fixed nand.h's ECCPOS. A conflict existed with POS5 and badblock
for non-JFFS2.
- Switched default ECC to be JFFS2.
- remove trailing white space, trailing empty lines, C++ comments, etc.
- split cmd_boot.c (separate cmd_bdinfo.c and cmd_load.c)
* Patches by Kenneth Johansson, 25 Jun 2003:
- major rework of command structure
(work done mostly by Michal Cendrowski and Joakim Kristiansen)
Fixed rarp boot method for IA32 and other little-endian CPUs.
* Patch by Marc Singer, 28 May 2003:
Added port I/O commands.
* Patch by Matthew McClintock, 28 May 2003
- cpu/mpc824x/start.S: fix relocation code when booting from RAM
- minor patches for utx8245
* Patch by Daniel Engstrm, 28 May 2003:
x86 update
* Patch by Dave Ellis, 9 May 2003 + 27 May 2003:
add nand flash support to SXNI855T configuration
fix/extend nand flash support:
- fix 'nand erase' command so does not erase bad blocks
- fix 'nand write' command so does not write to bad blocks
- fix nand_probe() so handles no flash detected properly
- add doc/README.nand
- add .jffs2 and .oob options to nand read/write
- add 'nand bad' command to list bad blocks
- add 'clean' option to 'nand erase' to write JFFS2 clean markers
- make NAND read/write faster
* Patch by Rune Torgersen, 23 May 2003:
Update for MPC8266ADS board
Add support for Atmel AT91RM9200DK w/NAND
* Patches by Robert Schwebel, 19 Mar 2003:
- use arm-linux-gcc as default compiler for ARM
- fix i2c fixup code
- fix missing baudrate setting
- added $loadaddr / CFG_LOAD_ADDR support to loadb
- moved "ignoring trailing characters" _before_ u-boot wants to
print out diagnostics messages; removes bogus characters at the
end of transmission
* Patch by John Zhan, 18 Mar 2003:
Add support for SinoVee Microsystems SC8xx boards
* Patch by Rolf Offermanns, 21 Mar 2003:
ported the dnp1110 related changes from the current armboot cvs to
current u-boot cvs. smc91111 does not work. problem marked in
smc91111.c, grep for "FIXME".
* Patch by Brian Auld, 25 Mar 2003:
Add support for STM flash chips on ebony board
* Add PCI support for MPC8250 Boards (PM825 module)
* Patch by Stefan Roese, 25 Mar 2003: