this rework is done in order to add a phylib and allow to have phy driver support
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this will allow to support 64bit platform
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
A "pure" initcall has no dependencies on anything else, and purely
initializes variables that couldn't be statically initialized.
This only exists for built-in code, not for modules.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
as autoconf.h is store in include/generated and not include/linux anymore
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this will be re-add as mach-at91
for now on keep the net driver which will be updated to new API
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
The mac address information is taken from the imx_iim driver if it's present.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This driver provides an interface for programming and sensing the IIM fusebox
which is present on some i.MX chips.
Since the IIM io addresses of the controlling registers and each fuse bank are
are not contiguous the driver implementation uses two drivers, imx_iim, and
imx_iim_bank. The imx_iim is the "parent" driver for a device holding the
map_base address of the control registers. The imx_iim_bank driver is for
child devices holding the map_base of each fuse bank. The platform code then,
instantiate one imx_iim_bank device per fuse bank.
Fuses blow is a dangerous operation. Thus, the fuses blow functionality can be
disabled independently at configuration time. On run time this functionality
must be enabled explicitly by setting the permanent_write_enable parameter.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This allows the use of IIM registers from code which is not mx35 specific.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
With this fix its possible to run loadb -f /dev/ram0
again with the latest next patchstack. Without you will
run into data_abort. Tested with omap3530 beagleboard.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This repairs a bug which came with patch "0cb00c1 omap nand: cleanup"
We first have to set ecc.layout before we can use it and should
do the nand_scan_tail after we set the ecc.mode.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
with cm-regbits-34xx.h and codebase from linux kernel
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
with the following support
uart 0 & 1
network
nand
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Andrea GALLO <andrea.gallo@stericsson.com>
Cc: Gael SALLES <gael.salles@stericsson.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Jean-Christophe PLAGNIOL-VILLARD
Sascha Hauer
Michael Grzeschik
Baruch Siach