The FSF address has changed; The FSF site says that
address is
Free Software Foundation
51 Franklin Street, Fifth Floor
Boston, MA 02110-1301
USA
(see http://www.fsf.org/about/contact/)
Instead of updating it each time the address changes,
just drop it completely treewide.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The mxs nand driver has a calculation for the ecc strength.
This calculation was not used for some common nands and it
was assumed that 2k page nands always have a ecc strength
of 8. This is not true since there are devices with 224 bytes
of oob instread of 64 bytes. These allow for a greater ecc
strength. Since the kernel relies on the calculation and
we have to be consistent with the kernel use the calculcation
in barebox aswell and just remove our assumptions.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch does probably too much, but it's hard (and very
cumbersome/time consuming) to break it out. What is does is this:
* each command has one short description, e.g. "list MUX configuration"
* made sure the short descriptions start lowercase
* each command has one usage. That string contains just the
options, e.g. "[-npn]". It's not part of the long help text.
* that is, it doesn't say "[OPTIONS]" anymore, every usable option
is listed by character in this (short) option string (the long
description is in the long help text, as before)
* help texts have been reworked, to make them
- sometimes smaller
- sometimes describe the options better
- more often present themselves in a nicer format
* all long help texts are now created with BUSYBOX_CMD_HELP_
macros, no more 'static const __maybe_unused char cmd_foobar_help[]'
* made sure the long help texts starts uppercase
* because cmdtp->name and cmdtp->opts together provide the new usage,
all "Usage: foobar" texts have been removed from the long help texts
* BUSYBOX_CMD_HELP_TEXT() provides the trailing newline by itself, this
is nicer in the source code
* BUSYBOX_CMD_HELP_OPT() provides the trailing newline by itself
* made sure no line gets longer than 77 characters
* delibertely renamed cmdtp->usage, so that we can get compile-time
errors (e.g. in out-of-tree modules that use register_command()
* the 'help' command can now always emit the usage, even without
compiled long help texts
* 'help -v' gives a list of commands with their short description, this
is similar like the old "help" command before my patchset
* 'help -a' gives out help of all commands
Signed-off-by: Holger Schurig <holgerschurig@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The old output of "help" was just producing a long list, that usually
scrolled of the screen (even on a X11 terminal). This list is more
compact, and also sorted by groups.
The old output format (plus grouping) is now available with 'help -v'.
Example:
Information commands:
?, devinfo, help, iomem, meminfo, version
Boot commands:
boot, bootm, go, loadb, loads, loadx, loady, saves, uimage
...
Signed-off-by: Holger Schurig <holgerschurig@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We need list_for_each_entry_safe in dev_remove_bb_dev since the
list entries are removed during iteration over the list.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reported-by: Alexander Aring <alex.aring@gmail.com>
This refactors the code so that we get a mtd_add_bb which can
be used to create a bb dev on a mtd_info.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The devfs layer just adds an addition indirection between mtd
and the bb devices with no purpose. Drop it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Was tested on NAND with {writesize=4096, oobsize=224} and
{writesize=2048, oobsize=64}.
This patch will not break any NAND that was working
before. Implemented calculation way may be used for other NAND chips
with writesize == 2048 but oobsize != 64.
Signed-off-by: Dmitry Lavnikevich <d.lavnikevich@sam-solutions.com>
Signed-off-by: Grigory Milev <g.milev@sam-solutions.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Since i.MX6 has only one R/B actual pin, if there are several R/B
signals (from different NAND chips) they must be connected to this
pin.
Signed-off-by: Dmitry Lavnikevich <d.lavnikevich@sam-solutions.com>
Signed-off-by: Grigory Milev <g.milev@sam-solutions.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
I am using an sam5d35 and its pmecc nand ecc controller.
In barebox, using similar atmel_nand.c the system crashes.
The problem was a call to chip->ecc.hwctl from nand_write_subpage_hwecc
(nand_base.c) when we write a sub page.
chip->ecc.hwctl function is not set when we are using PMECC controller.
As a workaround, i set NAND_NO_SUBPAGE_WRITE for PMECC controller in
order to disable sub page access in nand_write_page.
I think we can have the same problem in Linux. I do not performed
subpage nand writes from Linux but i made the following patch according
to my Barebox defect.
Signed-off-by: Herve Codina <Herve.CODINA@celad.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The string pointed to isn't modified, so declare it as const.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Right now we do not support persistent names for mtd devices. The
base name can be passed to add_mtd_device, but this is always appended
with a dynamic number. With this patch add_mtd_device takes a device_id
argument which can be used to create a mtd device with an exact name.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
when the bootmode is different than NAND (USB for example), the
GPMI clock is not enabled thus we can't probe a NAND flash.
Tested on an i.MX28
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The i.MX6 uses the same GPMI NAND controller as i.MX23/28 do. This adds
i.MX6 support to the driver.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
As the apbh dma engine is also found on i.MX6 move the header file
out of MXS specific directories.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
MXS specific devices have some common infrastructure in the kernel
known as STMP devices. We have the same in barebox, but with a
mxs_ prefix instead of a stmp_ prefix. As some STMP devices are
also found on i.MX6 move the common infrastructure out of MXS
specific files and use the stmp_ prefix.
This is done in preparation for i.MX6 NAND support.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This updates the NAND stuff to Linux-3.11-rc1. It is synchronized
as best as we can get:
- locks removed
- The splitting in different files we had to better support different
features has been dropped. Instead this is now done mostly with the
use of __maybe_unused
Some barebox adjustments are forward ported, like:
- Allow partial page writes
- Optionally allow to erase bad blocks
- check for all_ff before writing a page
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This introduces the ecc stength fields in the structures and fills
them in, but leaves them unused right now.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This is based on Linux:
commit e2414f4c20bd4dc62186fbfd7bdec50bce6d2ead
Author: Brian Norris <computersforpeace@gmail.com>
Date: Mon Feb 6 13:44:00 2012 -0800
Currently, the flash-based BBT implementation writes bad block data only
to its flash-based table and not to the OOB marker area. Then, as new bad
blocks are marked over time, the OOB markers become incomplete and the
flash-based table becomes the only source of current bad block
information. This becomes an obvious problem when, for example:
* code accessing the flash cannot read the flash-based BBT format
* BBT is corrupted and the flash must be rescanned for bad
blocks; we want to remember bad blocks that were marked from Linux
So to keep the bad block markers in sync with the flash-based BBT, this
patch changes the default so that we write bad block markers to the proper
OOB area on each block in addition to flash-based BBT. Comments are
updated, expanded, and/or relocated as necessary.
The new flash-based BBT procedure for marking bad blocks:
(1) erase the affected block, to allow OOB marker to be written cleanly
(2) update in-memory BBT
(3) write bad block marker to OOB area of affected block
(4) update flash-based BBT
Note that we retain the first error encountered in (3) or (4), finish the
procedures, and dump the error in the end.
This should handle power cuts gracefully enough. (1) and (2) are mostly
harmless (note that (1) will not erase an already-recognized bad block).
The OOB and BBT may be "out of sync" if we experience power loss bewteen
(3) and (4), but we can reasonably expect that on next boot, subsequent
I/O operations will discover that the block should be marked bad again,
thus re-syncing the OOB and BBT.
Note that this is a change from the previous default flash-based BBT
behavior.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Chipsize didn't take number of LUNs into account. Sync chipsize calculation
to kernel commit 63795755
Tested with MT29F8G16ADBDAH4 on OMAP4
Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this fix the problems introduced when detecting non ONFI flashes in
commit 4c2bdc8728
"nand_base: detect more ONFI flash"
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Antony Pavlov
Sascha Hauer
Holger Schurig
Alexander Shiyan
Dmitry Lavnikevich
Herve Codina
Uwe Kleine-König
Eric Bénard
张忠山
Jan Luebbe
Jan Weitzel