Also definition can be modified in arch/arm/boards/pcm043/lowlevel.c,
but I am not sure is we can call imx_silicon_revision() from
board_init_lowlevel().
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Arm needs 64-Bit alignment of the oftree as mentioned in the documentation
Documentation/arm/Booting.
Other architectures may need a bigger alignment so align to 4K.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The intention of this code was to check the return value of fdt_open_into. Fix
this.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
So we can use it for dhcp request too.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This will allow to understand what happened.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This will allow to execute any file and detect it's type to handle it.
This will allow to use shell for bootp bootfile or dfu.
You can register multiple hook for the same filetype. They will be execute
in the invert order of register. If a hook does not handle the file you just
return -ERESTARTNOHAND;
This is only available with hush parser.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
So we can use it for dhcp request too.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Backport 2 fixes back from Linux kernel (title verbatim from
Linux kernel log) :
- docg3 fix in-middle of blocks reads
- docg3 reduce read alignment burden
These 2 enable partial reads from the MTD (ie. read only the
111 first bytes), which enable linux kernel booting or UBIFS
from barebox.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
As per MMC spec, once power has been applied to an SD card, the card
can take as much as 250ms to complete its power-up cycle, and become
responsive to CMD0.
When this delay was not in place, activating the SD card in the env
init failed sometimes. With it, no more failure are observed.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The pxamci driver was not waiting for the BUSY line to be
deasserted. This was specifically breaking the CMD12 at
the end of block multiple writes, when the SD card had not
time enough to commit the last write.
Fix it by waiting for PRG_DONE bit (which is actually the
busy signal end condition).
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The pxamci requires a bit to be set in the command control
register when a CMD12 is sent. Set it, as required in the
PXA Developer Manuel, chapter "Stop Data Transmission
Command (CMD12 or IO/Abort with CMD52)".
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
When preparing a command, apply a mask so that only the command part
will be used for the switch case. This will be more robust
for future command response types.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Fix clock handling accordingly to PXA manual :
- enable the MMC controller clock once and for all
- only disable the MMC bus clock when changing the MMCLK by
adjusting the clock ratio, else let the controller and SD
card shut down the clock as the see fit.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Instead of using hard encoded values in the code, use defines to setup
the timeouts of reads/writes/commands.
Fix the read timeout as defined in the PXA Developer Manual.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This is a brown paper bag type of bugs. Do not assume that a file
has to be at minimun 512 bytes to be detectable.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Supported devices:
- nand
- ethernet
- mmc0, mmc1 (on stk5v3 development board)
- led (on stk5v3 development board)
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Was missing in net_init and net_new.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
So we can use the menu for the xloader too.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
instead of assuming the backingstore is a ip address, use resolv()
to make it possible to pass in a hostname.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
'nameserver' and 'domainname' should be globally available variables
specific to networking. Register a 'net' device to store these variables.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Currently all devices have an id meaning that all devicenames
end with a number. This patch adds a DEVICE_ID_SINGLE to make
it ppossible to register a device without an id assigned to
it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This makes it possible to pass a command sequence to the automount
command instead of only a script (a command sequence would get confused
by the additional argument)
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds the scripts/mkcompile_h from the Kernel. This gives
us additional information about the build like who built this binary
and with which compiler. Currently the only information used is the
build timestamp and the generation number.
This also fixes the build timestamp in the banner which is now correct
even with consecutive builds without making clean in between.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Juergen Beisert
Alexander Shiyan
Sascha Hauer
Steffen Trumtrar
Jean-Christophe PLAGNIOL-VILLARD
Robert Jarzmik
Christian Kapeller