bugfix/all/firmware_class-return-specific-errors-from-file-read.patch
and
bugfix/all/firmware_class-log-every-success-and-failure.patch needed
some substantial changes as similar but incomplete fixes have been
made upstream.
svn path=/dists/trunk/linux/; revision=20912
Drop/refresh patches as appropriate. Disable aufs for now.
Two of our longstanding patches finally went upstream.
CONFIG_MAGIC_SYSRQ_DEFAULT_MASK was renamed in the process so adjust
config accordingly.
svn path=/dists/trunk/linux/; revision=20909
1. Reset or remove values for config symbols that were only
configurable if EXPERT.
2. Set additional configurable symbols to their default values.
This should have no effect on the actual configuration, except for
sh4 where EXPERT is *always* set and so the settings in 1 were
still being followed.
svn path=/dists/trunk/linux/; revision=20825
These drivers used to be conditional on USB_PHY (which we disabled)
but now they select it. Disable them all and let individual configs
(and other symbols) enable the drivers.
svn path=/dists/trunk/linux/; revision=20788
Restrict creation of user namespaces to root (CAP_SYS_ADMIN) by default
(sysctl: kern.unprivileged_userns_clone)
svn path=/dists/trunk/linux/; revision=20773
Leave it enabled for armel/{iop32x,ixp4xx,kirkwood,orion5x} and m68k.
Drop the workaround patch for powerpc.
svn path=/dists/sid/linux/; revision=20732
These symbols were either (1) removed entirely or (2) merged or
renamed, and we already configure the other symbol.
svn path=/dists/trunk/linux/; revision=20604
This driver doesn't bind to any device IDs, and instead has a comment
saying that the serial_cs and hci_uart drivers should be used instead.
So there's not much point in building it.
svn path=/dists/trunk/linux/; revision=20559
Disable most platform drivers, SPI and I2C drivers at the top level.
Platform drivers should be selected by architecture and flavour
configurations, and generally are. SPI and I2C devices aren't easily
detectable and their drivers aren't auto-loaded, so again they should
usually be selected in specific configuration files and probed
according to board code or FDTs.
As exceptions, I2C hwmon devices may be probed by lm-sensors and many
media tuners include I2C devices which are probed with the help of the
higher-level device driver. I've tried to be conservative and also
left I2C iio, input, leds and misc devices alone for now.
Disable the regulator subsystem at the top level as only some
architectures will need it.
Disable MTD_NAND_PLATFORM, PDA_POWER and FB_S1D13XXX on x86, as these
don't appear likely to be used on any x86 system that could run our
generic kernel images.
svn path=/dists/trunk/linux/; revision=20556
USB_EHCI_ROOT_HUB_TT adds about 10 lines of code and is safe even if
not needed, so it's never worth turning off.
USB_EHCI_TT_NEWSCHED was 'new' in 2006 and is now the default, so
hardly anyone will be testing the 'old' code now.
svn path=/dists/trunk/linux/; revision=20546
These devices need platform data (even for SDIO) and apparently are
only used with ARM boards at the moment.
svn path=/dists/trunk/linux/; revision=20543
We currently set it to m, but it's no longer buildable as a module and
it really doesn't make sense to enable it at all in the generic
config.
svn path=/dists/trunk/linux/; revision=20538
Due to the way cgroup subsystems are tracked, changing any of them
between built-in and modular is an ABI change, so don't change this
right now.
svn path=/dists/sid/linux/; revision=20520
Ben Hutchings
Bastian Blank