This fixes a number of broken links throughout the
tree, mostly caused by wiki.asterisk.org being replaced
with docs.asterisk.org, which should eliminate the
need for sporadic fixes as in f28047db36.
Resolves: #430
(cherry picked from commit 8f5581b0d0)
Internally, chan_dahdi only applies callgroup and
pickupgroup to FXO signalled channels, but this is
not documented anywhere. This is now documented in
the sample config, and a warning is emitted if a
user tries configuring these settings for channel
types that do not support these settings, since they
will not have any effect.
Resolves: #294
(cherry picked from commit 945babf25c)
This adds support for Called Subscriber Held for FXS
lines, which allows users to go on hook when receiving
a call and resume the call later from another phone on
the same line, without disconnecting the call. This is
a convenience mechanism that most real PSTN telephone
switches support.
ASTERISK-30372 #close
Resolves: #240
UserNote: Called Subscriber Held is now supported for analog
FXS channels, using the calledsubscriberheld option. This allows
a station user to go on hook when receiving an incoming call
and resume from another phone on the same line by going on hook,
without disconnecting the call.
(cherry picked from commit 52283301e8)
Currently, if an FXS channel is still off hook when
all calls on the line have hung up, the user is provided
reorder tone until going back on hook again.
In addition to not reflecting what most commercial switches
actually do, it's very common for switches to automatically
reoriginate for the user so that dial tone is provided without
the user having to depress and release the hookswitch manually.
This can increase convenience for users.
This behavior is now supported for kewlstart FXS channels.
It's supported only for kewlstart (FXOKS) mainly because the
behavior doesn't make any sense for ground start channels,
and loop start signalling doesn't provide the necessary DAHDI
event that makes this easy to implement. Likely almost everyone
is using FXOKS over FXOLS anyways since FXOLS is pretty useless
these days.
ASTERISK-30357 #close
Resolves: #224
UserNote: The autoreoriginate setting now allows for kewlstart FXS
channels to automatically reoriginate and provide dial tone to the
user again after all calls on the line have cleared. This saves users
from having to manually hang up and pick up the receiver again before
making another call.
(cherry picked from commit c16cc93a4b)
sig_analog allows users to flash and use the three-way dial
tone as a primitive hold function, simply by never timing
it out.
Some systems allow this dial tone to time out to silence,
so the user is not annoyed by a persistent dial tone.
This option allows the dial tone to time out normally to
silence.
ASTERISK-30004 #close
Resolves: #205
UserNote: The threewaysilenthold option now allows the three-way
dial tone to time out to silence, rather than continuing forever.
(cherry picked from commit 5516763e57)
When immediate=yes on an FXS channel, sig_analog will
start fake audible ringback that continues until the
channel is answered. Even if it answers immediately,
the ringback is still audible for a brief moment.
This can be disruptive and unwanted behavior.
This adds an option to disable this behavior, though
the default behavior remains unchanged.
ASTERISK-30003 #close
Resolves: #118
UserNote: The immediatering option can now be set to no to suppress
the fake audible ringback provided when immediate=yes on FXS channels.
(cherry picked from commit d87abb2ec9)
A previous change, ASTERISK_29991, made it possible
to send additional Caller ID parameters that were
not previously supported.
This change adds support for analog DAHDI channels
to now be able to receive these parameters for
on-hook Caller ID, in order to enhance the usability
of CPE that support these parameters.
Resolves: #94
ASTERISK-30331
UserNote: Additional Caller ID properties are now supported on
incoming calls to FXS stations, namely the
redirecting reason and call qualifier.
(cherry picked from commit 87f44dc0f9)
Currently, both pulse and tone dialing are always enabled
on all FXS lines, with no way of disabling one or the other.
In some circumstances, it is desirable or necessary to
disable one of these, and this behavior can be problematic.
A new "dialmode" option is added which allows setting the
methods to support on a per channel basis for FXS (FXO
signalled lines). The four options are "both", "pulse",
"dtmf"/"tone", and "none".
Additionally, integration with the CHANNEL function is
added so that this setting can be updated for a channel
during a call.
Resolves: #35
ASTERISK-29992
UserNote: A "dialmode" option has been added which allows
specifying, on a per-channel basis, what methods of
subscriber dialing (pulse and/or tone) are permitted.
Additionally, this can be changed on a channel
at any point during a call using the CHANNEL
function.
(cherry picked from commit 82d7bb49dd)
Currently, chan_dahdi will wait for at least one
ring before an incoming call can enter the dialplan.
This is generally necessary in order to receive
the Caller ID spill and/or distinctive ringing
detection.
However, if neither of these is required, then there
is nothing gained by waiting for one ring and this
unnecessarily delays call setup. Users can now
use immediate=yes to make FXO channels (FXS signaled)
begin processing dialplan as soon as Asterisk receives
the call.
ASTERISK-30305 #close
Change-Id: I20818b370b2e4892c7f40c8a8753fa06a81750b5
Currently, if any custom ring cadences are specified, they are
appended to the array of cadences from wherever we left off
last time. This works properly the first time, but on subsequent
dahdi restarts, it means that the existing cadences are left
alone and (most likely) the same cadences are then re-added
afterwards. In short order, the cadence array gets maxed out
and the user begins seeing warnings that the array is full
and no more cadences may be added.
This buggy behavior persists until Asterisk is completely
restarted; however, if and when dahdi restart is run again,
then the same problem is reintroduced.
This fixes this behavior so that cadence parsing is more
idempotent, that is so running dahdi restart multiple times
starts adding cadences from the beginning, rather than from
wherever the last cadence was added.
As before, it is still not possible to revert to the default
cadences by simply removing all cadences in this manner, nor
is it possible to delete existing cadences. However, this
does make it possible to update existing cadences, which
was not possible before, and also ensures that the cadences
remain unchanged if the config remains unchanged.
ASTERISK-29990 #close
Change-Id: Ie32ea3e8a243b766756b1afce684d4a31ee7421d
Correct typos of the following word families:
password
excludes
undesirable
checksums
through
screening
interpreting
database
causes
initiation
member
busydetect
defined
severely
throughput
recognized
counter
require
indefinitely
accounts
ASTERISK-29714
Change-Id: Ie8f2a7b274a162dd627ee6a2165f5e8a3876527e
This changeset is intended to address compatibility issues encountered
when interfacing Asterisk to electromechanical telephone switches that
implement ANI-B, ANI-C, or ANI-D.
In particular the behaviours that this impacts include:
- FGC-CAMA did not work at all when using MF signaling. Modified the
switch case block to send calls to the correct part of the
signaling-handling state machine.
- For FGC-CAMA operation, the delay between called number ST and
second wink for ANI spill has been made configurable; previously
all calls were made to wait for one full second.
- After the ANI spill, previous behavior was to require a 'ST' tone
to advance the call. This has been changed to allow 'STP' 'ST2P'
or 'ST3P' as well, for compatibility with ANI-D.
- Store ANI2 (ANI INFO) digits in the CALLERID(ANI2) channel variable.
- For calls with an ANI failure, No. 1 Crossbar switches will send
forward a single-digit failure code, with no calling number digits
and no ST pulse to terminate the spill. I've made the ANI timeout
configurable so to reduce dead air time on calls with ANI fail.
- ANI info digits configurable. Modern digital switches will send 2
digits, but ANI-B sends only a single info digit. This caused the
ANI reported by Asterisk to be misaligned.
- Changed a confusing log message to be more informative.
ASTERISK-29518
Change-Id: Ib7e27d987aee4ed9bc3663c57ef413e21b404256
Analog phones dial overlap dialing and it is chan_dahdi's job to read the
numbers. It has three timeout constants that this commit converts to
channel-level configuration options:
* firstdigit_timeout: Default time (ms) to detect first digit
* interdigit_timeout: Default time (ms) to detect following digits
* matchdigit_timeout: Default time (ms) to wait in case of ambiguous
match. This happens when the dialed digits match a number in the current
context but are also the prefix of another number.
Change-Id: Ib728fa900a4f6ae56d1ed810aba61b6593fb7213
Support for referring to DAHDI channels by logical names was added in
(FIXME: when? Asterisk 11? 1.8?) and was intended to be part of support
of refering to channels by name.
While technically usable, it has never been properly supported in
dahdi-tools, as using it would require many changes at the Asterisk
level. Instead logical mapping was added at the kernel level.
Thus it seems that refering to DAHDI channels by name is not really used
by anyone, and therefore should probably be removed.
Change-Id: I7d50bbfd9d957586f5cd06570244ef87bd54b485
The new option allows the channel driver's faxdetect option to timeout on
a call after the specified number of seconds into a call. The new feature
is disabled if the timeout is set to zero. The option is disabled by
default.
* Don't clear dsp_features after passing them to the dsp code in
my_pri_ss7_open_media(). We should still remember them especially for the
new faxdetect_timeout option.
ASTERISK-26214
Reported by: Richard Mudgett
Change-Id: Ieffd3fe788788d56282844774365546dce8ac810
Some telco switches occasionally ignore ISDN RESTART requests. The fix
for ASTERISK-19608 added an escape clause for B channels in the restarting
state if the telco ignores a RESTART request. If the telco fails to
acknowledge the RESTART then Asterisk will assume the telco acknowledged
the RESTART on the second call attempt requesting the B channel by the
telco. The escape clause is good for dealing with RESTART requests in
general but it does cause the next call for the restarting B channel to be
rejected if the telco insists the call must go on that B channel.
chan_dahdi doesn't really need to issue a RESTART request in response to
receiving a cause 44 (Requested channel not available) code. Sending the
RESTART in such a situation is not required (nor prohibited) by the
standards. I think chan_dahdi does this for historical reasons to deal
with buggy peers to get channels unstuck in a similar fashion as the
chan_dahdi.conf resetinterval option.
* Add the chan_dahdi.conf force_restart_unavailable_chans compatability
option that when disabled will prevent chan_dahdi from trying to RESTART
the channel in response to a cause 44 code.
ASTERISK-25034 #close
Reported by: Richard Mudgett
Change-Id: Ib8b17a438799920f4a2038826ff99a1884042f65
Naveen Albert
Josh Soref
Sarah Autumn
Tzafrir Cohen
Sean Bright
Richard Mudgett
Matthew Jordan