diff --git a/Makefile b/Makefile
index 2636ac055e..96cca232be 100644
--- a/Makefile
+++ b/Makefile
@@ -2380,8 +2380,23 @@ MPC837XERDB_config:	unconfig
 MVBLM7_config: unconfig
 	@$(MKCONFIG) $(@:_config=) ppc mpc83xx mvblm7 matrix_vision
 
-sbc8349_config:		unconfig
-	@$(MKCONFIG) $(@:_config=) ppc mpc83xx sbc8349
+sbc8349_config \
+sbc8349_PCI_33_config \
+sbc8349_PCI_66_config: unconfig
+	@mkdir -p $(obj)include
+	@if [ "$(findstring _PCI_,$@)" ] ; then \
+		$(XECHO) -n "... PCI HOST at " ; \
+		echo "#define CONFIG_PCI" >>$(obj)include/config.h ; \
+	fi ; \
+	if [ "$(findstring _33_,$@)" ] ; then \
+		$(XECHO) -n "33MHz... " ; \
+		echo "#define PCI_33M" >>$(obj)include/config.h ; \
+	fi ; \
+	if [ "$(findstring _66_,$@)" ] ; then \
+		$(XECHO) -n "66MHz... " ; \
+		echo "#define PCI_66M" >>$(obj)include/config.h ; \
+	fi ;
+	@$(MKCONFIG) -a sbc8349 ppc mpc83xx sbc8349
 
 SIMPC8313_LP_config \
 SIMPC8313_SP_config: unconfig
diff --git a/doc/README.sbc8349 b/doc/README.sbc8349
index 908e7680a6..2c35919f28 100644
--- a/doc/README.sbc8349
+++ b/doc/README.sbc8349
@@ -91,19 +91,37 @@ safety check before resetting the board upon completion of the reflash.
 PCI:
 ====
 
-This board and U-Boot have been tested with PCI built in, on a SBC8349
-and confirmed that the "pci" command showed the intel e1000 that was
-present in the PCI slot.  Note that if a 33MHz 32bit card is inserted
-in the slot, then the whole board will clock down to a 33MHz base
-clock instead of the default 66MHz.  This will change the baud clocks
-and mess up your serial console output.  If you want to use a 33MHz PCI
-card, then you should build a U-Boot with #undef PCI_66M in the
-include/configs/sbc8349.h and store this to flash prior to powering down
-the board and inserting the 33MHz PCI card.
+There are three configuration choices:
+	sbc8349_config
+	sbc8349_PCI_33_config
+	sbc8349_PCI_66_config
 
-By default PCI support is disabled to better support very early
-revision MPC834x chips with possible PCI issues.  Also PCI support is
-untested on the sbc8347 variants at this point in time.
+The 1st does not enable CONFIG_PCI, and assumes that the PCI slot
+will be left empty (M66EN high), and so the board will operate with
+a base clock of 66MHz.  Note that you need both PCI enabled in u-boot
+and linux in order to have functional PCI under linux.  The only
+reason for choosing to not enable PCI would be if you had a very
+early (rev 1.0) CPU with possible PCI issues.
 
+The second enables PCI support and builds for a 33MHz clock rate.  Note
+that if a 33MHz 32bit card is inserted in the slot, then the whole board
+will clock down to a 33MHz base clock instead of the default 66MHz.  This
+will change the baud clocks and mess up your serial console output if you
+were previously running at 66MHz.  If you want to use a 33MHz PCI card,
+then you should build a U-Boot with sbc8349_PCI_33_config and store this
+to flash prior to powering down the board and inserting the 33MHz PCI
+card.
 
-						Paul Gortmaker, 01/2007
+The third option builds PCI support in, and leaves the clocking at the
+default 66MHz.  This has been tested with an intel PCI-X e1000 card.
+This is also the appropriate choice for people with a recent (non 1.0)
+CPU who currently have the PCI slot physically empty, but intend to
+possibly add a PCI-X card at a later date.
+
+   => pci
+   Scanning PCI devices on bus 0
+   BusDevFun  VendorId   DeviceId   Device Class       Sub-Class
+   _____________________________________________________________
+   00.00.00   0x1957     0x0080     Processor               0x20
+   00.11.00   0x8086     0x1026     Network controller      0x00
+   =>
diff --git a/include/configs/sbc8349.h b/include/configs/sbc8349.h
index 868bd54a6a..088b28356c 100644
--- a/include/configs/sbc8349.h
+++ b/include/configs/sbc8349.h
@@ -40,24 +40,28 @@
 #define CONFIG_MPC8349		1	/* MPC8349 specific */
 #define CONFIG_SBC8349		1	/* WRS SBC8349 board specific */
 
-#undef CONFIG_PCI
 /* Don't enable PCI2 on sbc834x - it doesn't exist physically. */
 #undef CONFIG_MPC83XX_PCI2		/* support for 2nd PCI controller */
 
-#define PCI_66M
-#ifdef PCI_66M
-#define CONFIG_83XX_CLKIN	66000000	/* in Hz */
-#else
+/*
+ * The default if PCI isn't enabled, or if no PCI clk setting is given
+ * is 66MHz; this is what the board defaults to when the PCI slot is
+ * physically empty.  The board will automatically (i.e w/o jumpers)
+ * clock down to 33MHz if you insert a 33MHz PCI card.
+ */
+#ifdef PCI_33M
 #define CONFIG_83XX_CLKIN	33000000	/* in Hz */
+#else	/* 66M */
+#define CONFIG_83XX_CLKIN	66000000	/* in Hz */
 #endif
 
 #ifndef CONFIG_SYS_CLK_FREQ
-#ifdef PCI_66M
-#define CONFIG_SYS_CLK_FREQ	66000000
-#define HRCWL_CSB_TO_CLKIN	HRCWL_CSB_TO_CLKIN_4X1
-#else
+#ifdef PCI_33M
 #define CONFIG_SYS_CLK_FREQ	33000000
 #define HRCWL_CSB_TO_CLKIN	HRCWL_CSB_TO_CLKIN_8X1
+#else	/* 66M */
+#define CONFIG_SYS_CLK_FREQ	66000000
+#define HRCWL_CSB_TO_CLKIN	HRCWL_CSB_TO_CLKIN_4X1
 #endif
 #endif