It allows for much better control on the lifecycle of the session, and
already shows some missing tear down paths in case of errors.
It also clarifies the existence of "sess" pointer in several paths.
The code also becomes clearer overall, since all the transitions and
logic to send next messages are put together.
Tear down of the session will be integrated into gsm-sm in a follow-up
patch.
The 5gc session setup is only partially moved to gsm-sm, and left as an
exercise for users wishin to improve 5gc support.
In the past only GTPv2C was supported, and had the "gtp" generic prefix.
Later on, GTPv1C support was added, and "gtp1" prefix was used.
Let's move GTPv2C specific bits to have "gtp2" prefix too, and leave
"gtp" prefix for generic stuff among different GTP versions.
This commit adds EMM Cause to Attach accept message when
Attach Request has COMBINED EPS IMSI ATTACH but the HSS
Network-Access-Mode is configure for EPS ONLY.
The use of the Gy interface (SMF acting as CTF towards an OCS node) is
mandated through configuration file. Default value "enable: auto" will
only make use of it in case a Diameter peer announcing support for the
Credit-Control Application is found.
Upon subscriber session creation, and after auth check over Gx, the SMF
will create a Gy session with the OCS and only after that step the SMF
will accept the session back to the subscriber.
The OCS may then grant some traffic volumes/time and ask to be notified
back with updated measurements.
In order to get the measurements, the SMF relies on PFCP URR configured
to the UPF through Session Repoort Request messages.
When closing the subscriber session, the SMF will also terminate the Gy
session at the OCS.
So far only some specifics parts of the Gy interface as well as the PFCP
side are implemented. Those should be enough to at least have
volume/time thresholds granted by the OCS, which then will be able to
track subsriber resource use.
This patch doesn't implement the OCS side of the Gy interface, that's
left as a future exercise. The interface was tested using an OCS
emulator implemented in TTCN-3 [1]
[1] https://cgit.osmocom.org/osmo-ttcn3-hacks/
TODO:
* Use an event for the report, like SMF_EVT_N4_TIMER?
* Properly set Service identifier in Gy CCR
* SMF: Properly set pkt/octet volumes in Gy CCR
** Update when receiving PFCP Modify Response.
* Figure out best way to require Gy through config file in open5gs-smfd.
* Create a new sess-sm.c which handles smf_sess_t state through
Gx+Gy+PFCP creation, modification and tear down. This way we can do
stuff in parallel, for instance Gx+Gy. It will alsoavoid duplicating
some code paths due to Gy being optional.
Catch Origin-Host during CCA and set it as Destination-Host during
subsequent CCRs. This way we ensure UPDATE/TERMINATION Requests are sent
back explicitly to the same Diameter peer. Moreover, it seems
freediameter relies on this AVP to properly send the message over the
correct SCTP association when several diameter peers are available.
1. UE registered and PDU established.
2. PCF does not receive Heartbeat.
- PCF De-registered state.
- Since PDU is established, SMF should not remove NF instance
3. PCF re-registered.
- HERE, WE NEED TO INCREASE NF REFERENCE COUNT.
Otherwise, NF instance will be removed if PCF is de-registered state
4. UE sends PDU release request.
5. Because SMF knows PCF NF instance, SMF can send PCF delete
As per 3GPP TS 23.401 version 15.12.0, section 5.3.1.2.2
The PDN GW allocates a globally unique /64
IPv6 prefix via Router Advertisement to a given UE.
After the UE has received the Router Advertisement message, it
constructs a full IPv6 address via IPv6 Stateless Address
autoconfiguration in accordance with RFC 4862 using the interface
identifier assigned by PDN GW.
For stateless address autoconfiguration however, the UE can
choose any interface identifier to generate IPv6 addresses, other
than link-local, without involving the network.
And, from section 5.3.1.1, Both EPS network elements and UE shall
support the following mechanisms:
/64 IPv6 prefix allocation via IPv6 Stateless Address
autoconfiguration according to RFC 4862, if IPv6 is
supported.
* [SMF] Gn: Avoid assert crash if no PDP resources available
* [SMF] Gn: Rearrange IE handling order in CreatePDPContextRequest
Let's handle the GTPC remote addr + TEID first, since those should be
used in the CreatePDPContextResponse ideally if available.
Let's then handle parsing of all IEs not related to bearers/UserPlane,
then those missing, and finally do all the IP resource allocation.
* Fix conversion from IPFilterRule to packet filter
As per 3GPP TS 24.008, following Packet filter component type identifier
are not supported on the LTE pre release-11 UEs:
IPv4 local address type
IPv6 remote address/prefix length type
IPv6 local address/prefix length type
And,
IPv6 remote address/prefix length type and
IPv6 local address/prefix length type shall be used when both MS and
Network support Local Address in TFTs.
This commit add logic to omit adding local address in packet filters
for compatibility with pre-release LTE 11 devices. The following parameter
could be used to toggle omit/no to omit behavior.
parameter:
no_ipv4v6_local_addr_in_packet_filter: <true/false>
* Remove logic of supporting pre-release LTE 11 devices in PCRF
Sukchan Lee
Pau Espin
Supreeth Herle
EugeneBogush